Digox 5 is a new concept in oxygen measurement in beverage production.

Its all-new electronics open up numerous possibilities for oxygen measurement and data processing in the laboratory and in production. The tried and tested measuring method employing an open electrode is reliable, exact and maintenance-free.

The automatic calibration system, which, in just a few seconds, can check and correct the measuring sensitivity of the sensor, provides the user with absolute dependability for the accuracy of measurement values at any time.

The Digox 5 makes possible both individual or test measurements and continuous monitoring of your plant.
　

The Thiedig sensor - The intelligent measuring system

- The Thieidg sensor works on the basis of the cathodic reduction of oxygen at a
  polarised electrode.

- The Thiedig sensor makes use of this principle by means of the potentiostatic
  arrangement of three electrodes.

- Unlike in other measuring methods the sample liquid (beer or other beverage) is
  itself used as an electrolyte, and the measurement is performed directly without
  the need for a membrane.

- This results in very fast response times.If oxygen penetration occurs, then the
  measuring cell is automatically rinsed free. The oxygen level does not need to be reduced in the cell.

The advantages :

- The sensor works drift-free and is reliable

- Extremely short response time due to direct contact with the sample

- Unlike membrane sensors the system allows exact temperature compensation
  over a wide range

- The nature of the system means that there is no zero-point drift

- The sensitivity of the sensor can be checked at any time without interrupting
  measurement

Accuracy at all times

The advantages of Thiedig active calibration   

- The automatic calibration provides you with complete dependability in the
  shortest possible time

- The measurement values can be double-checked by re-calibrating at any time
  without interruption to measurements

- Since calibration takes place in the measurement sample, there are no external
  effects from any other substance

- The data are stored automatically and can be recalled and recorded

DIGOX 5 - The ideal instrument for process control

The Digox 5 is the ideal instrument for trace oxygen monitoring as part of overall process control. It is ready at all times without long preparation or run-in times.

The integrated automatic calibration allows the checking of the measuring sensitivity during the first measurement and so ensures the total dependability of the measurement data.

The addition of the touch memory system and the new data logger enables clear, unmistakable allocation of the oxygen values and the accompanying measurement conditions to the respective measuring point,

date, time and process controller. The Digox 5 can be deployed at any point of the production process.

Measurements in degasified water are possible as measurements in beer wort or unfiltered liquid.

A high-power, nickel-metal hybrid accumulator battery allows for more than 8 hours of independent operation.

Information required about each measurement process is provided via the units clearly laid out display. straightforward messages provide information about the operating state or problems, so that exact measurements are guaranteed at any time. As an all-round, portable instrument the Digox 5 is the ideal control instrument for checking permanently installed equipment,or as a variably employed solution for small plants, or else as a substitute for malfunctioning permanent oxygen detectors.

In this application, the power supply comes via the mains power adapter, without affecting the capacity of the accumulator.

DIGOX 5 - Measuring instrument plus intelligent software

The Digox 5 features a high-powered electronic control unit. The self explanatory menu operation and straightforward graphic display make it simple and convenient to work with the new instrument.

All parameters relevant for the measuring, as well as the date and time, are displayed simultaneously.

Together with our new Digox WIN software and touch memory system, the new electronic unit provides a variety of new applications.

All these features mean that the Digox5 is able to measure,record and sort data.

The touch memory system

"Touch-memories" are small data stores that can be programmed individually.

Made of stainless steel, they are no larger than a small coin. They can be attached anywhere and require no maintenance.

Touch-memories enable the individual identification of each measuring point.

Digox 5 can store each identification code in its data logger, and thus be able to assign each measurement to a particular measuring point. Mix-ups are therefore impossible.

The time and date, as well as the time of previous measurements can be checked.